Some models of parker cylinders, parker cylinder piston seals

The American PARKER P1D series cylinder is a completely new and very advanced product. After decades of research and study, Parker has conducted a lot of research, used a lot of resources, superb technology and rich experience. Finally, the P1D series of cylinders was successfully created.


Parker P1D cylinder is a completely new ISO standard, based on high standard design, suitable for any possible application, whether it is simple or complex, and has three categories:
The first category: Parker P1D comprehensive general-purpose cylinder. This category of cylinder is usually suitable for various occasions, and its high performance and long service life have been recognized by most people.
Category 2: Parker P1D clean cylinder, with smooth surface design, integrated performance, practical adjustable sensor system, and compliance with strict hygiene requirements.
The third category: Parker P1D flexible interface type cylinder. This type of cylinder is small in size. It is an innovative design that saves space. The interface can also be made at the front or rear end of the cylinder.



Parker P1D standard cylinder
This is a completely new and innovative cylinder that will stand up to any challenge in the future. This kind of cylinder is double-acting, with a new type of air buffer. The sensor groove is light in weight, high in hardness, easy to install, and can protect the sensor.
The installation dimensions comply with international standards: ISO6431, ISO/DIS15552, VDMA24562 and AFNOR installation dimension standards. Can be used by customers worldwide.

Some models of PARKER P1D series cylinders:
P1D-B100MS-0025
P1D-B100MS-0040
P1D-B100MS-0050
P1D-B100MS-0080
P1D-B100MS-0100
P1D-B100MS-0125
P1D-B100MS-0160
P1D-B100MS-0200
P1D-B100MS-0250
P1D-B100MS-0320
P1D-B100MS-0400
P1D-B100MS-0500
P1D-B040MS-0025
P1D-B040MS-0040
P1D-B040MS-0050





parker cylinder piston seal


1. O-ring series
It has products made of various materials such as fluorine rubber, nitrile rubber, silicone, etc., which are widely used in various machinery and are resistant to various petroleum-based oils and various chemical media: the use of non-rubber types can meet the temperature of -60℃-+300℃ Area, use pressure range: <10MPa (hydraulic), <1MPa (pneumatic) <16MPa (static seal) of nitrile rubber and gasoline-resistant parts (90, 93, 97) expansion rate is 0.


2. Y-shaped sealing ring
Products made of fluorine rubber, nitrile rubber, chlorine rubber and other materials are widely used in hydraulic, mechanical, pneumatic and other industries. The resistant petroleum-based oil has excellent wear resistance, and different rubber types can be used to meet the temperature range of -60℃-+300℃.

3. Silicone rubber series
Equipped with advanced testing equipment and clean dust-free workshop. Products are widely used in electronics, medical equipment, food and other industries.
The rubber types are selected from a variety of domestic and imported silica gels, and the operating temperature can meet the requirements of -60°-+300°C. The products can meet the requirements of oil resistance, steam resistance, medical and edible fully transparent, high strength, flame retardant, conductive silicone rubber, etc.

4. Fluorine rubber series products
Parker cylinder piston sealing ring The fluororubber series products produced by the company are widely used in automobiles, shipbuilding, military industry, electronic appliances and other industries. The working temperature is -40℃+300℃, and can withstand fuel oil, high temperature, Freon, and overheating. Water, steam and excellent chemical resistance, customers are welcome to purchase and customize.

5. PTFE series products
PTFE gaskets are resistant to high temperatures and corrosion. They do not interact with concentrated acids, alkalis or strong oxidants at high temperatures. They have been widely used as sealing materials and are suitable for pipes, flanges, reactors, etc. Sealing devices on kettles, valves and containers. Special-shaped parts are produced according to user design drawings.

6. Various special-shaped miscellaneous parts
The materials are made of nitrile, natural, fluorine rubber, silicone, etc., which are widely used in automobiles, machinery, valves and other industries. Different types of rubber can be used to meet the temperature range of -50℃-+250℃.